The latest DSP technologies developed for the IC-7800/7700 plus over 45 years
of analog circuit expertise give the IC-7600 the performance advantage. The flagship's lineage:
dual DSP units, 3kHz 1st (roofing) filter, double-conversion superheterodyne, all direct descendents
of the IC-7800/7700.
- Dual DSP: Separate DSP units for transmitter/receiver and spectrum scope.
- Ist IF Filter: Three built-in 1st IF (roofing) filters – 3, 6 and 15 kHz.
- Receiver System: The double-conversion superheterodyne system and the image rejection mixer improve inband IMD.
- Display: 5.8-inch WQVGA (400×240 pixels)ultra-wide viewing angle TFT display with long-life
- Spectrum Scope: High-resolution real-time spectrum scope using a dedicated DSP unit.
- USB Connectors: Easily connect keyboards, flash memory drives and PCs.
- PSK Operation: Built-in PSK and RTTY operation with a USB keyboard - PC not required.
Dual DSP for
transmitter/receiver and spectrum scope
Two separate 32-bit DSP units power the transmitter/receiver and
spectrum scope. These processors give the IC-7600 high
performance comparable to our top-of-the-line IC-7800 and
IC-7700, thanks to the combination of dual DSP and our analog RF
104dB dynamic range and +30dBm third-order intercept point (IP3)
Icom's long years of analog RF circuit experience combined with
the latest digital technology results in an astonishing 104dB
receiver dynamic range and +30dBm IP3 in the HF bands without
sacrificing receiver sensitivity. Even a weak signal adjacent to
strong signals is clearly received by the IC-7600.
Double conversion superheterodyne dramatically improves inband
The IC-7600 employs a double conversion superheterodyne system
which has an image rejection mixer for the 2nd mixer stage. When
compared to a typical triple-conversion system, the double
conversion system is more difficult to implement but it
dramatically reduces signal distortion and provides a
high-fidelity RF signal to the DSP processor.
Dual AGC loops controlled by DPS
The IC-7600 has dual AGC loops, one analog and one digital, both
under DSP control. This architecture prevents strong adjacent
signals from "pumping" the AGC and allows maximum dynamic range
in the DSP.
Three built-in 1st IF (roofing) filters, including 3kHz
The IC-7600 has three built-in 1st IF filters ahead of the 1st IF amplifier stage.
The 3kHz filter is especially effective in CW and SSB modes to eliminate overloading
caused by strong signals just outside the passband.
Digital IF filter
The IC-7600 DSP allows you to "build your own" digital IF
filter. You can quickly choose bandwidth, shape factor and
center frequency, so that you can work that rare DX station
while your competition's still tweaking their transceiver
controls. There filter memories allow you to change filter
settings instantly, a great help during contesting or other
Digital twin PBT
After "building your own" digital IF filter, you can use digital
twin Passband Tuning (PBT) to shift and narrow the IF passband
until the interference is gone and you can clearly hear that
Digital notch filter
Signals such as heterodynes and AM carriers can be eliminated
with automatic notch filter technology, making interference from
RF sources such as beat signals and RTTY signals a thing of the
past. You can also choose three shape factors for the notch
filter, to optimize interference rejection.
The processing power of the 32-bit DSP producers results you can
hear! The 16-step variable noise reduction can significantly
enhance the receiver's signal-to-noise ratio, giving you a
clean, clear audio signal that may make the difference between
making the contract or not.
A 100-step digital noise blanker reduces interference from
pulse-type noise sources such as engine ignition systems.
Dualwatch allows you to receive two signals in the same band
simultaneously. For example, you can listen to a DX station
transmitting on 14.025MHz while also listening to the pileup
calling him on 14.030MHz
High stability TCXO unit
The IC-7600 provides ±0.5ppm frequency stability using a high
stability temperature-compensate crystal oscillator (0°C to +50°C)
This high stability during continuous transmission on RTTY or
5.8 inch ultra-wide viewing angle TFT display
The IC-7600's ultra-wide viewing angle display has excellent
color rendition and high contrast ratio with fast response time.
These features allow the spectrum scope and simulated analog
meters to move smoothly and naturally. While LED backlighting
offers faster start-up; stable brightness and very long life.
The dedicated spectrum scope DSP with built-in digital filtering
greatly improves dynamic range, response team and frequency
accuracy of the spectrum scope. The scope automatically selects
the optimum resolution based on the sweep bandwidth. In
addition, the spectrum scope range can be set independently from
the receiving frequency. You can monitor band conditions between
the selected sweep edges (Max. 500kHz) in the fixed mode, as
well as sweep a selected bandwidth centered on the receiving
frequency in the center mode.
Digital voice memory
With digital voice memory, you can record the incoming signal
and immediately replay the audio, a must-have feature for DXing
and contesting. Because the transceiver is recording
continuously, time-shhift playback can replay the 15 seconds of
audio that you heard <before> you pushed the Rec button!
The IC-7600 has a 4-channel transmit memory (maximum
90 seconds per channel) and 20 channel receive
memory (maximum 30 seconds per channel, total 200
seconds with 20 channels). In addition, the recorded
incoming signal can be saved on a USB flash drive.
The multi-function meter allows you to observe the
transmit/receive conditions at a glance. In addition to the
signal strength, transmit power level, ALC, compression level
and SWR meters, the IC-7600 shows the drain terminal voltage of
the final amplifier (Vd), the drain current of the final
amplifier (Id) and temperature of the PA circuit (TEMP).
RF speech compressor
The digital RF compressor boosts average RF output power,
improving signal strength and readability.
RTTY /PSK31 operation with a USB keyboard
Simply plug in a USB keyboard to operate RTTY and PSK! The
digital twin-peak filter greatly reduces interference and a
Triple band stacking register
The triple band stacking register quickly memorizes and calls up
the operating frequency and mode for 3 channels on each band.
Just push the band key button (ten-key pad), and you can call up
the last operating frequency and mode. This function is
convenient especially when switching bands during contests, etc.
Programmable band edge beep
You can program the band edge not only according to the amateur
radio band plan but also more specific frequencies like contest
frequencies, CW operating mode, etc. If you try to operate on
the OFF band, the transceiver alerts you with a beep sound. You
can also inhibit transmitting in the OFF band.
Built-in memory keyer
Built-in memory keyer provides 4 channels for CW mode and 8
channels each for RTTY and PSK31 modes, capable of storing up to
70 characters for each channel. The memory keyer is useful for
sending CQ or exchanging numbers during contests. When not
contesting, you can store and send your name, QTH, rig, etc,
With a USB keyboard, you can send memory contents using function
key on the keyboard.
USB connectors on the front and rear panel
The IC-7600 has one USB connector on the front panel and one on
the rear panel. You can connect a USB keyboard or USB flash
drive to the front panel (type A plug) and connect a PC to the
rear panel (type B plug). Using the CI-V data format and
external software*, you can control the IC-7600 from a PC via the
USB port. You can also transfer audio, both transmit and
receive, via the USB port.
*Software is not supplied from Icom.
Microphone equalizer and adjustable transmit bandwidth
The built-in audio equalizer has separate bass and
treble adjustments for a total of 121 combinations,
so you can adjust the tonal quality of your voice as
you want. In addition, the transmit bandwidth is
selectable from 100, 200, 300, 500Hz at the lowpass
edge, and 2500, 2700, 2800, 2900Hz at the high-pass
edge respectively. Three types of high and low
combinations can be stored in the memory as favorite
settings. With this flexibility of DSP-based
waveform shaping, transmit audio quality is
adjustable to your preference.
High power final amplifiers
For amplifier keying (SEND jack), you can select either a
mechanical relay (max. 16V/500mA) or a FET switch (max.
250V/200mA). The FET switch is designed to key older tube-type
amplifiers that may have high voltage on the SEND line.
Two types of send relay settings
The noise reduction separates the target signal from random noise components. By
using the excellent performance of the 32-bit floating point DSP, this separation
is made immediately without a delay and extracts signals from noise components.
The noise reduction suppression level is variable in 16 steps to adjust the balance
between the S/N ratio and clarity.
Built-in high-speed automatic antenna tuner
the antenna tuner memorizes its settings based on your transmit
frequency, so that it can rapidly tune when you change bands.
High-voltage capacitors allow continuous-duty-cycle full-power
- Two Tx/Rx antenna connectors with automatic antenna selector
- Rx antenna In/Out connector for receiver
antenna or external alttenuator
- General coverage receiver covers from 30kHz to 60MHz
(* Some frequency bands are not guaranteed, depending on version)
- Two types of receiver preamplifiers: Preamp 1: Increase low
level signal improving intermodulation characteristics Pream 2:
High gain preamplier
- Built-in 3-step RF attenuator (6,12 and 18dB)
- Tx monitor
- 50 CTCSS tone encoder and decoder
- All mode power control
- VOX capability (Voice operated transmission)
- Multi-function electronic keyer with adjustable keying speed, dot-dash ratio and
paddle polarity and bug key function
- DSP controlled CW keying waveform shaping
- Frequency lock function for split operation
- The normal (default) CW carrier point is selectable from USB and LSB
- APF (audio peak filter) function with soft/sharp filter shape
- Double key jack system
- Full break-in function and semi break-in function
- CW pitch control from 300 to 900Hz
- Adjustable CW envelope
- Set mode function for flexible and speedy setting
- Memory pad stores up to 10 (or 5) operating frequencies
- Quick split function enables split operation with a single action
- Digital meter indicates output power, ALC level, SWR, COMP
(compression level), Id (drain current of the final amplifier)
and VD (voltage of the final amplifer)
- Single knob control from squelch volume to RF gain
- RIT and ∂Tx variable up to ±9.999kHz
- Quick RIT/∂TX clear function
- UTC/Local Clock and timer function
- 1Hz pitch tuning and 1Hz indication
- 101 memory channels with 10-character comment
- Built-in voice synthesizer announces operating frequency, mode and receiving signal
- Programmed scan, memory scan, select memory scan, VSC scan and ∂F scan
- Auto tuning step function
- Band edge beep
- Main dial tension control and dial lock
- CI-V interface capability and RS-232C connector for PC connection
- AH-4 control circuit
- Triple band stacking register
- FFT scope wave averaging function
- Screen saver function
13.8V, 100W-class HF/6m transceiver
4-pin DC power connector on rear panel
3 roofing filters (Performance in DW reduced due to roofing
+30 dBm IP3
Single USB port on front (USB thumb drive/keyboard, TBD)
Single USB port on rear (Rig Control)
APF/TBF (Twin Bandpass Filter for Digital)
Separate RX-OUT and RX-IN antenna ports
Audio controls similar to IC-7700
Spectrum Scope features identical to IC-7700
AM/CW auto tune
- Icom’s proven IF-DSP technology
Power output: 100W
MOSFET PA with 2 x RD100HHF1
IC-7600 is a mid-range transceiver between
IC-7800/IC-7700 and IC-7000/IC-7200
Plain English menus allow rapid change of set mode
settings and features
Selectable roofing filters: 3kHz, 6kHz, and 15kHz
Double superhet with an image-rejection 2nd mixer
Vastly improved in-band IMD with image-reject 2nd
Dynamic range 104dB, IP3 = +30dBm
Two 32-bit floating-point DSPs. TI TMS320C6726 for TX and RX; TI
TMS320C6720 for the spectrum scope.
5.8 inch (diagonal) color LCD with a long life, quick-start LED backlight
Digital meter scales display Po, ALC, SWR,
COMP, VD, ID, PA temperature
RTTY and PSK31 encoder/decoder
CW rise-time adjustment range 2 ~ 10 mS
Two USB ports
TCXO: 0.5ppm in the range 0 - 50°C
Mechanical relay (16V/0.5A) and FET relay (250V/200mA)
for keying external amplifier
#- CHS-IC-7600 #