Limited to Stock on Hand
Comes with a 90 day Warranty
New Crystal Roofing Filters provide ultimate weak signal receiver performance in crowded, strong signal environments.
The amazing Crystal Roofing Filter performance
has been proven in the FT DX 5000!
The Down conversion 9 MHz 1st IF frequency receiver construction, can realize narrow 300 Hz (optional), 600 Hz and 3 kHz bandwidth roofing filters.
Implementing the extra sharp Crystal Roofing Filters provides superior close-in
dynamic range and affords the best receiver performance possible.
Outstanding receiver performance
is the heritage of the FT DX 5000
The essential elements in receiver performance are the RF amplifier and the 1st mixer.
YAESU pursued the ultimate performance of these circuits. The RF amplifier has
optimized NF points, and the over-sized wide range RF transformer exhibits minimum
saturation in strong signal processing. The optimized devices were selected to
guarantee superior multi-signal RX performance. The desired maximum performance
has been realized in the development of the
FTDX3000 receiver circuitry. The FTDX3000
has the high dynamic range IP3 performance
that was realized and proven in the FTDX5000.
IF DSP provides effective and optimized QRM rejection
The 32 bit high speed floating decimal DSP (max 2800 MIPS) provides effective
cancellation/reduction (DNR) of the random noise that is frequently frustrating in
the HF frequencies. Also: the AUTO NOTCH (DNF) that automatically eliminates
the dominant beat tone, the CONTOUR, and the APF, are very effective receiver
noise reduction tools in the HF bands operations. The YAESU original DSP QRM
and noise reduction functions are provided.
Large and wide color LCD display
The 3.5-inch wide color LCD displays the operating information and the status of
the transceiver functions, with high resolution (480 x 272 dots) on the screen.
The various FTDX3000 functions are displayed on this LCD and provide the
operator with easy to read operating information.
High Speed Spectrum Scope built-in
Although the FTDX3000 has only one receiver, a high speed Spectrum Scope is
built into the radio. When in the Auto Mode, the Spectrum Scope display is
updated in real time. The maximum bandwidth of the scope is 1 MHz, and the
minimum span width setting is 20 kHz. The best desired span is selectable for the
high resolution display. The current band activity can be monitored in real time.
AF SCOPE display and RTTY/PSK encoder/decoder (optional)
Optional AF SCOPE and optional RTTY encoder/decoder functions have been
The wave form of the AF SCOPE signal can be displayed on the TFT LCD. Also,
the RTTY/PSK text may be displayed on the LCD.
Independent Frequency display
The Main operating frequency is the most important display in the radio, VFO-A
frequency is located just above the main dial. The newly developed LCD has a
wider viewing angle and higher contrast for convenient and effortless viewing.
- The specialized Receiver amplifier for 50 MHz is built in
- Three antenna connectors are provided.
The “ANT-3” terminal may be assigned to “RX-only”
- Signal output for an external receiver and the 9 MHz IF output are furnished
- High speed Automatic antenna tuner built in
- Optional μ-tune unit available
- USB interface equipped
RX Frequency Range: 30 kHz - 56 MHz (operating)
1.8 MHz - 54 MHz (specified performance, Amateur bands only)
TX Frequency Ranges: 1.8 MHz - 54 MHz (Amateur bands only)
Frequency Stability: ±0.5 ppm (after 1 minute @+14 °F to +122 °F [–10 °C to +50 °C])
Operating Temperature Range: +14 °F to +122 °F (–10 °C to +50 °C)
Emission Modes: A1A (CW), A3E (AM), J3E (LSB, USB), F3E (FM),
F1B (RTTY), F1D (PACKET), F2D (PACKET)
Frequency Steps: 1/10 Hz (SSB, CW, & AM), 100 Hz (FM)
Antenna Impedance: 50 Ohms, unbalanced
16.7 - 150 Ohms, unbalanced (1.8 - 29.7 MHz)
25 - 100 Ohms, unbalanced (50 - 54 MHz)
(Tuner ON, 1.8 MHz - 50 MHz Amateur bands, TX only)
Power Consumption (Approx.): RX (no signal) 1.8 A
RX (signal present) 2.1 A
TX (100 W) 23 A
Supply Voltage: DC 13.8 V ± 10% (Negative Ground)
Dimensions (WxHxD): 14.4” x 4.5” x 12.3” (365 x 115 x 312 mm)
Weight (Approx.): 22.0 lbs (10 kg)
Power Output: 5 - 100 watts (2 - 25 watts AM carrier)
Modulation Types: J3E (SSB): Balanced,
A3E (AM): Low-Level (Early Stage),
F3E (FM): Variable Reactance
Maximum FM Deviation: ±5.0 kHz/ ±2.5 kHz
Harmonic Radiation: Better than -60 dB (1.8 MHz - 29.7 MHz Amateur bands: Harmonics)
Better than -50 dB (1.8 MHz - 29.7 MHz Amateur bands: Others)
Better than -65 dB (50 MHz Amateur band)
SSB Carrier Suppression: At least 60 dB below peak output
Undesired Sideband Suppression: At least 60 dB below peak output
3rd-order IMD: –31 dB @14 MHz 100 watts PEP
Bandwidth: 3 kHz (LSB/USB), 500 Hz (CW), 6 kHz (AM), 16 kHz (FM)
Audio Response (SSB): Not more than -6 dB from 300 to 2700 Hz
Microphone Impedance: 600 Ohms (200 to 10k Ohms)
Circuit Type: Double-conversion Superheterodyne
Intermediate Frequencies: 9.000 MHz/ 30 kHz (24 kHz for AM/FM)
Sensitivity: SSB (BW: 2.4 kHz, 10 dB S+N/N)
4 μV (0.5 - 1.8 MHz) (IPO “ON”)
0.16 μV (1.8 - 30 MHz) (RF AMP 2 “ON”)
0.125 μV (50 - 54 MHz) (RF AMP 2 “ON”)
AM (BW: 6 kHz, 10 dB S+N/N, 30 % modulation @400 Hz)
28 μV (0.5 - 1.8 MHz) (IPO “ON”)
2 μV (1.8 - 30 MHz) (RF AMP 2 “ON”)
1 μV (50 - 54 MHz) (RF AMP 2 “ON”)
FM (BW: 15 kHz, 12 dB SINAD)
0.5 μV (28 - 30 MHz) (RF AMP 2 “ON”)
0.35 μV (50 - 54 MHz) (RF AMP 2 “ON”)
There is no specification for frequency ranges not listed.
Selectivity (WIDTH: Center): Mode -6 dB -60 dB
CW/RTTY/PKT 0.5 kHz or better 750 Hz or less
SSB 2.4 kHz or better 3.6 kHz or less
AM 6 kHz or better 15 kHz or less
FM 15 kHz or better 25 kHz or less
Image Rejection: 70 dB or better (1.8 MHz - 30MHz Amateur bands)
60 dB or better (50 - 54MHz Amateur band)
Maximum Audio Output: 2.5 W into 4 Ohms with 10% THD
Audio Output Impedance: 4 to 8 Ohms (4 Ohms: nominal)
Conducted Radiation: Less than 4 nW